DE
English
polski
русский
українська
Hood Lift Support 1K0-823-359-A
Verfügbar in Shops 14 Angebote
Fahrzeug-Passgenauigkeit 108 Fahrzeuge
Technische Daten
| OEM Part Number | 1K0823359A |
|---|---|
| Part Type | Gas-Filled Hood Lift Support Strut |
| Material | — |
| Extended Length | — |
| Compressed Length | — |
| Shaft Diameter | — |
| Body Diameter | — |
| Force Rating | — |
| Mounting Type | Clip-on end fittings (both ends) |
| Quantity Sold | Each (1 strut) |
So ersetzen Sie Hood Lift Support
Replacing the hood lift support on these VW models is a straightforward DIY job requiring no special tools. The strut clips onto ball-stud mounting points at both ends and can typically be swapped in under 30 minutes. Always support the hood manually or with a prop rod before removing the old strut.
-
Gather Materials and Park Safely
Park the vehicle on a level surface, turn off the engine, and allow it to cool fully. Have a prop rod or assistant ready to support the hood throughout the procedure.
-
Open the Hood and Secure It
Open the hood fully and prop it securely with a rod or have a second person hold it. Never rely on the failing strut to hold the hood during replacement.
-
Locate the Strut Mounting Points
Identify the two ball-stud mounting points — one on the hood panel and one on the body or inner fender. Note how the existing strut clips are oriented before removal.
-
Release the Lower Clip and Detach
Using a small flathead screwdriver or trim removal tool, carefully pry the retaining clip at the lower (body-side) ball stud and pull the strut end free from the stud.
-
Release the Upper Clip and Remove the Old Strut
Repeat the clip release process at the upper (hood-side) ball stud. Remove the old strut completely and set it aside for proper disposal.
-
Install the New Strut
Position the new 1K0823359A strut with the shaft end oriented upward (rod-end up is the standard orientation for hood struts). Snap the upper end onto the hood-side ball stud first, then press the lower end firmly onto the body-side ball stud until the clip seats with an audible click.
-
Test Operation and Verify
Remove the prop rod and lower the hood gently, then lift it again to verify the new strut holds the hood fully open without drifting. Confirm both clip ends are fully seated and secure before driving.
Anzeichen für ein verschlissenes Teil
-
Hood Will Not Stay Open
The most common symptom — the hood slowly drifts downward or falls closed after being raised, indicating the strut has lost gas pressure and can no longer support the hood's weight.
-
Visible Oil or Fluid Leakage
A shiny or oily residue on the strut body or shaft indicates the internal seal has failed and the gas/fluid charge is escaping, resulting in loss of support force.
-
Slow or Weak Hood Lift
The hood feels unusually heavy when opening or only rises partially before stopping, suggesting the strut is losing pressure but has not yet failed completely.
-
Unusual Noises During Hood Operation
Squeaking, clicking, or scraping sounds when opening or closing the hood may indicate a worn strut end clip, a dry ball stud, or internal strut degradation.
-
Strut Physically Detached or Bent
A strut that has popped off a ball stud or shows visible bending or physical damage must be replaced immediately to prevent hood damage or injury.
Wechselintervalle
Volkswagen service schedules do not list a mandatory replacement interval for hood lift supports. Service life depends on usage frequency, climate, and physical condition. Immediate replacement is recommended as soon as the hood fails to remain fully open.
Häufig gestellte Fragen
Is 1K0823359A a single strut or a pair?
Part number 1K0823359A is sold individually — one strut per unit. Many VW models in this fitment range use a single center-mounted or one side-mounted hood strut. Verify your specific vehicle's configuration, and consider buying two if your vehicle uses a pair.
Will this part fit my 2007 Volkswagen Jetta?
Yes. The 1K0823359A is confirmed compatible with the Volkswagen Jetta for model years 2005 through 2009. Always cross-check your vehicle's VIN with a VW dealer or trusted parts retailer to confirm fitment for your exact build.
Is the Stabilus 017510 a quality replacement for the OEM strut?
Yes. Stabilus is an OEM-tier manufacturer that supplies gas struts to major automakers, including Volkswagen. The Stabilus 017510 is a confirmed direct replacement for 1K0823359A and is the recommended aftermarket alternative.
Can I install this hood strut myself without professional help?
Yes. The strut uses clip-on end fittings and requires no special tools. The job typically takes under 30 minutes. The most important precaution is to securely prop the hood before removing the old strut to prevent injury.
Why does my hood strut fail faster in winter?
Cold temperatures cause the gas charge inside the strut cylinder to contract, reducing lift force. Repeated thermal cycling between extreme cold and heat accelerates seal wear, leading to earlier gas leakage and loss of support.
What is the difference between the OEM part and an aftermarket equivalent?
The OEM Volkswagen part (1K0823359A) is manufactured to exact factory specifications and is the guaranteed correct fitment. Quality aftermarket alternatives like Stabilus offer equivalent performance at a lower price point. Avoid unbranded or very low-cost struts, as inconsistent gas pressure and poor seal quality are common issues.
Fehler gefunden?
Helfen Sie uns, besser zu werden — wenn Sie einen Fehler auf der Website oder in den Daten entdeckt haben, teilen Sie uns dies mit, und wir beheben ihn so schnell wie möglich.