RU
Deutsch
English
polski
українська
Engine Oil Pan 06J-103-600-AF
Доступно в магазинах 21 предложение
Совместимость с автомобилями 153 автомобиля
Технические характеристики
| OEM Part Number | 06J-103-600-AF |
|---|---|
| Material | Metal |
| Engine Compatibility | 2.0L TSI |
| Oil Level Sensor Port | Yes (cover plate 03G-103-707 required if no sensor) |
| Mounting Bolts Required | 20 × N 910 967 01 |
| Bolt Torque Specification | ~10 Nm / 7 ft-lbs (verify with service manual) |
| Drain Plug | Included mounting provision; new drain plug gasket recommended at installation |
| Superseded / Interchangeable OEM Numbers | 06J-103-600-E, 06J-103-600-T, 06J-103-600-G |
Как заменить Engine Oil Pan
Replacing the engine oil pan on a 2.0L TSI VW/Audi vehicle is a moderate-difficulty job requiring proper vehicle support, complete oil drainage, and careful attention to sealing surfaces. Always consult your vehicle's factory service manual for model-specific torque values and procedures before beginning.
-
Preparation
Park the vehicle on a level surface and allow the engine to cool completely. Disconnect the negative battery terminal. Lift the vehicle safely and support it on rated jack stands.
-
Drain Engine Oil
Position a drain pan beneath the oil pan. Remove the oil drain plug and allow all engine oil to drain completely before proceeding.
-
Remove Obstructing Components
Remove any underbody panels or splash shields blocking access to the oil pan. Depending on the specific model, it may be necessary to detach the exhaust downpipe for adequate clearance.
-
Remove the Old Oil Pan
Loosen and remove all 20 mounting bolts securing the oil pan to the engine block. Gently pry the oil pan away from the engine block, taking care not to damage the mating surfaces.
-
Clean Mating Surfaces
Thoroughly remove all residual gasket material and old sealant from both the engine block and the new oil pan mating surfaces. Ensure both surfaces are completely clean and dry before applying new sealant.
-
Install New Oil Pan
If the vehicle is not equipped with an oil level sensor, install cover plate 03G-103-707 with its seal and securing nuts. Apply a bead of appropriate oil-resistant sealant to the oil pan mating surface. Position the pan against the engine block and hand-tighten all 20 mounting bolts.
-
Torque Bolts and Reassemble
Tighten all 20 mounting bolts in a crisscross pattern to ensure even clamping pressure. Torque bolts to approximately 10 Nm (7 ft-lbs) or the exact value specified in your service manual. Reinstall any exhaust components and underbody panels removed for access.
-
Refill Oil and Verify
Install a new drain plug gasket and torque the drain plug to specification. Refill the engine with the correct grade and quantity of oil. Start the engine, check for leaks around the pan seam and drain plug, and verify the oil level is correct on the dipstick.
Признаки износа детали
-
Oil Puddle Under Vehicle
A puddle of engine oil forming under the front of the vehicle after parking is a primary sign of oil pan damage, a failed pan gasket or sealant, or a cracked pan caused by road impact.
-
Low Oil Level Warning Light
If the oil level sensor detects a drop below minimum, the dashboard warning light will illuminate. A leaking oil pan can cause oil to drop to dangerous levels without an obvious external puddle.
-
Visible Oil Seepage at Pan Seam
Brown or black oily residue along the bottom seam of the engine block where the oil pan meets the block indicates sealant or gasket failure that will worsen over time.
-
Oil Pressure Warning
Severe oil loss from a cracked or heavily leaking oil pan can reduce oil pressure, triggering the low oil pressure warning light — a critical condition requiring immediate engine shutdown.
-
Physical Pan Damage
Visible dents, cracks, or holes in the oil pan caused by road debris, curb impacts, or bottoming out require immediate pan replacement to prevent catastrophic oil loss.
Периодичность замены
The oil pan itself does not have a fixed replacement interval under normal conditions. Service life depends on physical condition, sealing integrity, and any impact damage. Always inspect during routine oil changes and replace immediately if active leakage or structural damage is confirmed.
Часто задаваемые вопросы
What vehicles is the 06J103600AF oil pan compatible with?
This oil pan fits Volkswagen Group vehicles equipped with the 2.0L TSI engine, including the Audi A3 (2008–2013), Audi Q3 (2015–2016), Audi TT Quattro (2011–2014), VW Arteon (2019–2021), VW Beetle Turbo (2012–2013), VW CC (2009–2017), VW Eos (2009–2016), VW GTI (2010–2013), VW Jetta GLI (2011–2014), VW Passat (2009–2010), and VW Tiguan (2012–2017). Always confirm compatibility using your vehicle's specific engine code and model year.
Is a gasket included with the 06J103600AF oil pan?
This oil pan uses RTV sealant rather than a traditional stamped gasket. No gasket is included because the correct installation method requires applying an oil-resistant sealant (such as VW specification D 176 404 A2 or equivalent) directly to the mating surface. Purchase the appropriate sealant separately before beginning installation.
My vehicle does not have an oil level sensor — can I still use this pan?
Yes. This pan is designed for both sensor-equipped and non-sensor vehicles. If your vehicle does not have an oil level sensor, you must install cover plate 03G-103-707 with its seal and securing nuts to block the sensor port. Failing to do so will result in an immediate oil leak.
Are the OEM superseded numbers 06J-103-600-E, -T, and -G the same part?
Yes. Part numbers 06J-103-600-E, 06J-103-600-T, and 06J-103-600-G are earlier revisions of the same oil pan that have been superseded by the current -AF suffix. The -AF is the latest and correct version to order for all applicable fitments.
What aftermarket brands make a reliable replacement for this oil pan?
Rein Automotive (ESK0164), URO Parts (URO-009416), and Vaico (V10-1899) all produce direct aftermarket replacements for this oil pan. Rein Automotive is generally considered a strong aftermarket choice for VAG applications and is widely stocked by German specialty suppliers.
How many mounting bolts does the 06J103600AF oil pan require, and what is the torque specification?
Installation requires 20 mounting bolts, VW part number N 910 967 01. The bolts should be torqued to approximately 10 Nm (7 ft-lbs) in a crisscross pattern. Always verify the exact torque value in your vehicle's factory service manual, as slight variations may exist between model years.
Нашли ошибку?
Помогите нам стать лучше — если вы заметили ошибку на сайте или в данных, сообщите нам, и мы исправим её как можно скорее.