PartsBat PartsBat Beta
Język
DE EN PL RU UK
Zaloguj się
Serpentine Belt 06K-903-137-A — oryginalna część samochodowa
Serpentine Belt 06K-903-137-A — miniatura 1
Serpentine Belt 06K-903-137-A — miniatura 2
Serpentine Belt 06K-903-137-A — miniatura 3
Serpentine Belt 06K-903-137-A — miniatura 4

Serpentine Belt 06K-903-137-A

Nr katalogowy
06K-903-137-A 06k903137a 06k-903-137-a 06K903137A
Nazwy alternatywne
Serpentine Belt 2.0T VW 06L903137A Ribbed Belt VW Tiguan Accessory Drive Belt Jetta GLI Serpentine Belt 542R0718 Drive Belt
Zakres cen
$21 – $61
z 3 ofert
Oryginalne części 3
Części używane 0
Pasujące pojazdy 45
Porównaj 3 oferty

Dostępne w sklepach 3 oferty

leithvwcary.com Dostawca części samochodowych
1 sprzedawca 1 nowych
Leith Volkswagen
Autoryzowany dealer
$46
Inni sprzedawcy Dostawca części samochodowych
2 sprzedawców 2 nowych
Volkswagen
Nowa
$30 $21
Capitol Volkswagen
Nowa
$61

Dopasowanie do pojazdu 45 pojazdów

Rok Marka Model Nadwozie i wersja Silnik
2025 Volkswagen Jetta GLI Autobahn 2.0L L4 - Gas
2024 Volkswagen Jetta GLI 40th Anniversary Edition 2.0L L4 - Gas
2024 Volkswagen Jetta GLI Autobahn 2.0L L4 - Gas
2024 Volkswagen Tiguan S 2.0L L4 - Gas
2024 Volkswagen Tiguan SE 2.0L L4 - Gas
2024 Volkswagen Tiguan SE R-Line Black 2.0L L4 - Gas
2024 Volkswagen Tiguan SEL R-Line 2.0L L4 - Gas
2023 Volkswagen Jetta GLI Autobahn 2.0L L4 - Gas
2023 Volkswagen Tiguan S 2.0L L4 - Gas
2023 Volkswagen Tiguan SE 2.0L L4 - Gas
2023 Volkswagen Tiguan SE R-Line Black 2.0L L4 - Gas
2023 Volkswagen Tiguan SEL R-Line 2.0L L4 - Gas
2022 Volkswagen Jetta GLI Autobahn 2.0L L4 - Gas
2022 Volkswagen Tiguan S 2.0L L4 - Gas
2022 Volkswagen Tiguan SE 2.0L L4 - Gas
2022 Volkswagen Tiguan SE R-Line Black 2.0L L4 - Gas
2022 Volkswagen Tiguan SEL R-Line 2.0L L4 - Gas
2021 Volkswagen Jetta GLI Autobahn 2.0L L4 - Gas
2021 Volkswagen Jetta GLI S 2.0L L4 - Gas
2021 Volkswagen Tiguan S 2.0L L4 - Gas
2021 Volkswagen Tiguan SE 2.0L L4 - Gas
2021 Volkswagen Tiguan SE R-Line Black 2.0L L4 - Gas
2021 Volkswagen Tiguan SEL 2.0L L4 - Gas
2021 Volkswagen Tiguan SEL Premium R-Line 2.0L L4 - Gas
2020 Volkswagen Jetta GLI Autobahn 2.0L L4 - Gas
2020 Volkswagen Jetta GLI S 2.0L L4 - Gas
2020 Volkswagen Tiguan S 2.0L L4 - Gas
2020 Volkswagen Tiguan SE 2.0L L4 - Gas
2020 Volkswagen Tiguan SE R-Line Black 2.0L L4 - Gas
2020 Volkswagen Tiguan SEL 2.0L L4 - Gas
2020 Volkswagen Tiguan SEL Premium R-Line 2.0L L4 - Gas
2019 Volkswagen Jetta GLI 35th Anniversary Edition 2.0L L4 - Gas
2019 Volkswagen Jetta GLI Autobahn 2.0L L4 - Gas
2019 Volkswagen Jetta GLI S 2.0L L4 - Gas
2019 Volkswagen Tiguan S 2.0L L4 - Gas
2019 Volkswagen Tiguan SE 2.0L L4 - Gas
2019 Volkswagen Tiguan SEL 2.0L L4 - Gas
2019 Volkswagen Tiguan SEL Premium 2.0L L4 - Gas
2019 Volkswagen Tiguan SEL Premium R-Line 2.0L L4 - Gas
2019 Volkswagen Tiguan SEL R-Line 2.0L L4 - Gas
2019 Volkswagen Tiguan SEL R-Line Jet Black 2.0L L4 - Gas
2018 Volkswagen Tiguan S 2.0L L4 - Gas
2018 Volkswagen Tiguan SE 2.0L L4 - Gas
2018 Volkswagen Tiguan SEL 2.0L L4 - Gas
2018 Volkswagen Tiguan SEL Premium 2.0L L4 - Gas

Podobne części 3 części

Engine Water Pump 06L-121-012-L

Engine Water Pump

06L-121-012-L

od $19
Engine Coolant Thermostat 06J-121-113-C

Engine Coolant Thermostat

06J-121-113-C

od $67
Accessory Drive Belt Tensioner Assembly 03H-145-299-B

Accessory Drive Belt Tensioner Assembly

03H-145-299-B

od $70

Specyfikacja techniczna

OEM Part Number 06K 903 137 A
Belt Type V-Ribbed (Serpentine)
Width 21.36 mm
Length 1100 mm
Rib Count / Profile 6PK
Material EPDM (Ethylene Propylene Diene Monomer) rubber
Engine Application 4 Cyl 2.0L GAS
Compatible Makes Volkswagen (Jetta GLI, Tiguan), Audi, SEAT, Škoda, Cupra

Jak wymienić Serpentine Belt

Replacing the 06K903137A serpentine belt is a straightforward job for a competent DIYer with basic hand tools. The procedure requires relieving the spring-loaded belt tensioner, rerouting the new belt across all pulleys, and verifying correct seating before startup. Always photograph or sketch the existing belt routing before removal.

Szybkie wskazówki

  • Photograph belt routing from multiple angles before removal — a misrouted belt can destroy itself and damage pulleys within seconds of startup.
  • Inspect the automatic tensioner and all idler pulleys while the belt is off; a worn tensioner bearing is a common cause of belt noise and premature belt failure, and replacing them together saves a repeat repair.
  • Never use belt dressing sprays or silicone lubricants on an EPDM ribbed belt — they can cause slippage and accelerate degradation of the compound.
  • Confirm the 6PK rib profile seats flush in every pulley groove before releasing the tensioner; even a single rib off-track will shred the belt edge quickly.
  • Use a proper serpentine belt tool or 16mm wrench on the tensioner — improvised tools can slip and cause injury or damage the tensioner arm.
  • After the test run, re-check belt tracking with the engine off and cool to ensure no heat-induced shifts occurred on first start.

  1. Safety Preparation

    Turn off the vehicle, remove the key, and allow the engine to cool completely. Disconnect the negative battery terminal to prevent accidental starting during the repair.

  2. Access the Belt Area

    Remove any engine covers or plastic shrouds blocking access to the serpentine belt and tensioner. On some Jetta GLI and Tiguan models, a splash shield or wheel liner may need partial removal for side access.

  3. Photograph Belt Routing

    Before removing anything, photograph the existing belt routing around all pulleys. Most vehicles also have a belt routing diagram printed on a label in the engine bay — locate and reference it.

  4. Release the Tensioner

    Using a 16mm wrench or serpentine belt tool, rotate the automatic belt tensioner to relieve tension on the belt. Insert a locking pin or suitable retention tool into the tensioner hole to hold it in the released position.

  5. Remove the Old Belt

    With the tensioner locked, carefully slide the belt off each pulley in sequence. Note the condition of all pulleys (alternator, A/C compressor, power steering, idler) — replace any that show wobble or roughness.

  6. Route and Install the New Belt

    Route the new 06K903137A belt exactly as the old one was positioned, referring to your photographs or the engine bay diagram. Ensure the V-ribs seat fully and evenly in every pulley groove.

  7. Restore Tensioner and Verify Alignment

    Remove the locking pin and slowly release the tensioner onto the new belt. Visually inspect all pulley contact points to confirm the belt is centred, flat, and free of twists.

  8. Reassemble, Start, and Inspect

    Reinstall all removed covers and components. Reconnect the battery. Start the engine and observe the belt at idle for at least one minute, listening for squealing, slapping, or chirping noises that could indicate misrouting.

Oznaki zużycia części

  • Squealing or Chirping Noise

    A high-pitched squeal or intermittent chirp from the engine bay — especially on cold starts or when accessories load up — is the most common sign of a glazed, worn, or misaligned serpentine belt.

  • Visible Belt Damage

    Inspect the belt surface for longitudinal cracks, fraying rib edges, glazing (shiny, hardened surface), or chunks missing from the ribs. Any of these indicate the belt is overdue for replacement.

  • Battery or Charging Warning Light

    If the belt slips or fails entirely, the alternator stops charging the battery. A battery-shaped warning light or voltmeter reading below 13V at idle points to belt or alternator drive failure.

  • Heavy Power Steering Effort

    Increased steering effort or jerky power-assisted steering response can indicate the belt is slipping on the power steering pump pulley under load.

  • Air Conditioning Not Cooling

    A belt that has lost tension or broken will stop driving the A/C compressor, resulting in warm air from the vents even when the climate control is set to maximum cooling.

  • Belt Slapping or Flapping Sound

    A rhythmic slapping noise at idle or under acceleration can signal a severely worn belt with loose ribs, a failed tensioner no longer maintaining proper belt tension.

Częstotliwość wymiany

Standard Inspection Interval
60,000 miles
Visually inspect belt for cracks, glazing, fraying, and rib condition. Check tensioner and idler pulley bearing play at the same service.
Standard Replacement Interval
90,000 miles
Replace the belt proactively at 90,000 miles under normal driving conditions, even if no visible damage is present, to avoid unexpected failure.
Severe-Duty Replacement Interval
60,000 miles
Vehicles subjected to extreme heat, frequent short trips, heavy A/C use, towing, or dusty environments should have the belt replaced earlier at 60,000 miles.

Replacement intervals are general guidelines. Always consult your vehicle's specific service schedule or a qualified VW/Audi technician, as interval requirements can vary by model year and engine variant. Immediate replacement is warranted if any visible damage or noise is detected regardless of mileage.

Najczęściej zadawane pytania

Is part number 06K903137A the correct serpentine belt for my VW Tiguan 2.0T?

It is confirmed correct for the VW Tiguan S, SE, SE R-Line Black, SEL, SEL Premium, SEL Premium R-Line, and SEL R-Line with the 4-cylinder 2.0L GAS engine for model years 2018–2022. Always cross-check your vehicle's VIN or parts catalogue to confirm fitment for your specific build date.

Can I use a 6PK1100 aftermarket belt instead of the OEM 06K903137A?

Yes. Several reputable manufacturers — including SKF (VKMV 6PK1100), HUTCHINSON, OPTIBELT, and KAMOKA — produce 6PK1100 belts to OEM specifications. SKF is the recommended aftermarket choice due to its OEM supplier status with Volkswagen Group. Verify the rib profile and length match before fitting.

How long does it take to replace the serpentine belt on a VW Jetta GLI or Tiguan?

For a mechanically experienced DIYer with proper tools, the job typically takes 30–60 minutes. Additional time may be needed if engine covers or wheel liner panels must be removed for access.

Should I replace the belt tensioner at the same time as the serpentine belt?

It is strongly recommended. The automatic tensioner contains an internal spring and bearing that wear over time. Replacing a worn tensioner along with the belt prevents premature belt wear, eliminates belt noise, and avoids a repeat repair at a later date.

What happens if the serpentine belt breaks while driving?

A broken serpentine belt will immediately disable the alternator, power steering pump, and A/C compressor. The battery warning light will illuminate, power steering assist will be lost, and the battery will begin to drain. The vehicle should be pulled over safely and not driven further, as continued operation can lead to battery failure and a stalled engine.

Does part 06K903137A fit Audi vehicles as well?

The part number is shared across Volkswagen Group brands, and cross-reference sources confirm it applies to Audi, SEAT, Škoda, and Cupra vehicles using the same 2.0L engine platform. However, you must verify fitment against your specific Audi model, year, and engine code using the VIN before ordering.

Znalazłeś błąd?

Pomóż nam się rozwijać — jeśli zauważyłeś błąd na stronie lub w danych, daj nam znać, a naprawimy go jak najszybciej.