UK
Deutsch
English
polski
русский
Serpentine Belt 06K-903-137-A
Доступно в магазинах 3 пропозиції
Сумісність з автомобілями 45 автомобілів
Технічні характеристики
| OEM Part Number | 06K 903 137 A |
|---|---|
| Belt Type | V-Ribbed (Serpentine) |
| Width | 21.36 mm |
| Length | 1100 mm |
| Rib Count / Profile | 6PK |
| Material | EPDM (Ethylene Propylene Diene Monomer) rubber |
| Engine Application | 4 Cyl 2.0L GAS |
| Compatible Makes | Volkswagen (Jetta GLI, Tiguan), Audi, SEAT, Škoda, Cupra |
Як замінити Serpentine Belt
Replacing the 06K903137A serpentine belt is a straightforward job for a competent DIYer with basic hand tools. The procedure requires relieving the spring-loaded belt tensioner, rerouting the new belt across all pulleys, and verifying correct seating before startup. Always photograph or sketch the existing belt routing before removal.
-
Safety Preparation
Turn off the vehicle, remove the key, and allow the engine to cool completely. Disconnect the negative battery terminal to prevent accidental starting during the repair.
-
Access the Belt Area
Remove any engine covers or plastic shrouds blocking access to the serpentine belt and tensioner. On some Jetta GLI and Tiguan models, a splash shield or wheel liner may need partial removal for side access.
-
Photograph Belt Routing
Before removing anything, photograph the existing belt routing around all pulleys. Most vehicles also have a belt routing diagram printed on a label in the engine bay — locate and reference it.
-
Release the Tensioner
Using a 16mm wrench or serpentine belt tool, rotate the automatic belt tensioner to relieve tension on the belt. Insert a locking pin or suitable retention tool into the tensioner hole to hold it in the released position.
-
Remove the Old Belt
With the tensioner locked, carefully slide the belt off each pulley in sequence. Note the condition of all pulleys (alternator, A/C compressor, power steering, idler) — replace any that show wobble or roughness.
-
Route and Install the New Belt
Route the new 06K903137A belt exactly as the old one was positioned, referring to your photographs or the engine bay diagram. Ensure the V-ribs seat fully and evenly in every pulley groove.
-
Restore Tensioner and Verify Alignment
Remove the locking pin and slowly release the tensioner onto the new belt. Visually inspect all pulley contact points to confirm the belt is centred, flat, and free of twists.
-
Reassemble, Start, and Inspect
Reinstall all removed covers and components. Reconnect the battery. Start the engine and observe the belt at idle for at least one minute, listening for squealing, slapping, or chirping noises that could indicate misrouting.
Ознаки зношеної деталі
-
Squealing or Chirping Noise
A high-pitched squeal or intermittent chirp from the engine bay — especially on cold starts or when accessories load up — is the most common sign of a glazed, worn, or misaligned serpentine belt.
-
Visible Belt Damage
Inspect the belt surface for longitudinal cracks, fraying rib edges, glazing (shiny, hardened surface), or chunks missing from the ribs. Any of these indicate the belt is overdue for replacement.
-
Battery or Charging Warning Light
If the belt slips or fails entirely, the alternator stops charging the battery. A battery-shaped warning light or voltmeter reading below 13V at idle points to belt or alternator drive failure.
-
Heavy Power Steering Effort
Increased steering effort or jerky power-assisted steering response can indicate the belt is slipping on the power steering pump pulley under load.
-
Air Conditioning Not Cooling
A belt that has lost tension or broken will stop driving the A/C compressor, resulting in warm air from the vents even when the climate control is set to maximum cooling.
-
Belt Slapping or Flapping Sound
A rhythmic slapping noise at idle or under acceleration can signal a severely worn belt with loose ribs, a failed tensioner no longer maintaining proper belt tension.
Періодичність заміни
Replacement intervals are general guidelines. Always consult your vehicle's specific service schedule or a qualified VW/Audi technician, as interval requirements can vary by model year and engine variant. Immediate replacement is warranted if any visible damage or noise is detected regardless of mileage.
Часті запитання
Is part number 06K903137A the correct serpentine belt for my VW Tiguan 2.0T?
It is confirmed correct for the VW Tiguan S, SE, SE R-Line Black, SEL, SEL Premium, SEL Premium R-Line, and SEL R-Line with the 4-cylinder 2.0L GAS engine for model years 2018–2022. Always cross-check your vehicle's VIN or parts catalogue to confirm fitment for your specific build date.
Can I use a 6PK1100 aftermarket belt instead of the OEM 06K903137A?
Yes. Several reputable manufacturers — including SKF (VKMV 6PK1100), HUTCHINSON, OPTIBELT, and KAMOKA — produce 6PK1100 belts to OEM specifications. SKF is the recommended aftermarket choice due to its OEM supplier status with Volkswagen Group. Verify the rib profile and length match before fitting.
How long does it take to replace the serpentine belt on a VW Jetta GLI or Tiguan?
For a mechanically experienced DIYer with proper tools, the job typically takes 30–60 minutes. Additional time may be needed if engine covers or wheel liner panels must be removed for access.
Should I replace the belt tensioner at the same time as the serpentine belt?
It is strongly recommended. The automatic tensioner contains an internal spring and bearing that wear over time. Replacing a worn tensioner along with the belt prevents premature belt wear, eliminates belt noise, and avoids a repeat repair at a later date.
What happens if the serpentine belt breaks while driving?
A broken serpentine belt will immediately disable the alternator, power steering pump, and A/C compressor. The battery warning light will illuminate, power steering assist will be lost, and the battery will begin to drain. The vehicle should be pulled over safely and not driven further, as continued operation can lead to battery failure and a stalled engine.
Does part 06K903137A fit Audi vehicles as well?
The part number is shared across Volkswagen Group brands, and cross-reference sources confirm it applies to Audi, SEAT, Škoda, and Cupra vehicles using the same 2.0L engine platform. However, you must verify fitment against your specific Audi model, year, and engine code using the VIN before ordering.
Знайшли помилку?
Допоможіть нам стати кращими — якщо ви помітили помилку на сайті або в даних, повідомте нас, і ми виправимо її якнайшвидше.