UK
Deutsch
English
polski
русский
Oxygen Sensor 06K-906-262-CE
Доступно в магазинах 7 пропозицій
Сумісність з автомобілями 157 автомобілів
Технічні характеристики
| OEM Part Number | 06K906262CE |
|---|---|
| Supersedes | 06K906262E |
| Overall Length | 760 mm |
| Number of Circuits | 4 |
| Fitting Position | After catalytic converter (rear, lower / downstream) |
| Connector Type | Permanently attached pigtail with electrical connector |
| Compatible Engine Sizes | 1.8L and 2.0L gasoline |
| Bosch Equivalent Number | 0258030528 |
Як замінити Oxygen Sensor
Replacing the downstream oxygen sensor on compatible Volkswagen models is a straightforward task with basic hand tools and an oxygen sensor socket. Always allow the exhaust system to cool completely before beginning, and consult the vehicle service manual for model-specific torque values.
-
Safety Preparation
Park the vehicle on a level surface and apply the parking brake. Disconnect the negative battery terminal and allow the exhaust system to cool completely to prevent burns.
-
Raise and Support the Vehicle
Safely raise the vehicle using a floor jack and secure it on jack stands to gain clear access to the underside of the exhaust system behind the catalytic converter.
-
Locate the Downstream Sensor
Trace the exhaust system rearward from the catalytic converter to find the downstream (rear/lower) oxygen sensor. Confirm this is the correct position — after the cat — before proceeding.
-
Disconnect the Electrical Connector
Press the release tab and carefully unplug the sensor's pigtail connector from the vehicle wiring harness. Ensure the wire is free and not routed in a way that will hinder removal.
-
Remove the Old Sensor
Using a dedicated oxygen sensor socket (typically 22 mm), unscrew the sensor from the exhaust bung counterclockwise. If the sensor is seized, apply penetrating oil and allow it to soak before attempting removal.
-
Install the New Sensor
Check whether the new OEM sensor threads are pre-coated with anti-seize compound. If not, apply a small amount. Thread the new sensor in by hand first, then torque to the manufacturer-specified value per the vehicle service manual.
-
Reconnect and Route the Wiring
Plug the pigtail connector firmly into the vehicle harness until it clicks. Route the wire away from hot exhaust components and moving parts, securing it with any OEM clips or brackets.
-
Final Verification
Reconnect the negative battery terminal. Start the engine and let it reach operating temperature. Verify no exhaust leaks at the sensor bung and confirm the check engine light has cleared or use an OBD-II scanner to erase any stored fault codes.
Ознаки зношеної деталі
-
Check Engine Light
A failing downstream oxygen sensor commonly triggers a P0136, P0137, or P0138 DTC, illuminating the check engine light. Always confirm the fault code before replacing the sensor.
-
Decreased Fuel Efficiency
A degraded oxygen sensor can send inaccurate data to the ECU, causing the engine to run rich and consume more fuel than normal.
-
Rough Engine Idle
When the ECU receives erratic signals from a failing sensor, it may adjust the fuel mixture improperly, resulting in an unstable or rough idle.
-
Increased Exhaust Emissions
A malfunctioning downstream sensor reduces the ECU's ability to confirm catalytic converter performance, potentially causing the vehicle to fail an emissions inspection.
-
Engine Misfires
Incorrect air-fuel mixture caused by faulty sensor feedback can contribute to combustion irregularities and noticeable engine misfires under load or at idle.
Періодичність заміни
Unlike upstream (pre-cat) oxygen sensors on older platforms, Volkswagen does not specify a proactive replacement mileage for this downstream sensor. Replacement is condition-based and driven by confirmed fault codes or failed emissions testing.
Часті запитання
Is the 06K906262CE the upstream or downstream oxygen sensor?
It is the downstream (post-catalytic converter) sensor, located in the rear/lower position after the cat. It is not interchangeable with the upstream sensor, which is positioned before the catalytic converter.
What vehicles is this sensor compatible with?
The 06K906262CE fits select Volkswagen models including the Beetle (2013–2019), Jetta (2014–2018), and Passat (2014–2022) equipped with 1.8L or 2.0L gasoline engines. Always verify fitment using your VIN or engine code before ordering.
Is the Bosch 0258030528 a direct replacement for the 06K906262CE?
Yes. Bosch part number 0258030528 is an OE-equivalent direct replacement with identical specifications, including the 760 mm overall length and 4-circuit connector. It is the top-recommended aftermarket alternative.
Does the 06K906262CE supersede the 06K906262E?
Yes. The CE suffix supersedes the earlier E suffix part. If your vehicle was originally fitted with 06K906262E, the 06K906262CE is the current correct replacement part.
Do I need to apply anti-seize compound when installing the new sensor?
Check the sensor threads before installation. Many OEM sensors arrive with threads pre-coated. If threads are bare, apply a small amount of anti-seize to prevent future seizure. Do not apply additional compound over a pre-coated sensor.
Will the check engine light clear automatically after replacing the sensor?
In many cases the ECU will clear the code after a successful drive cycle, but it is best practice to use an OBD-II scanner to manually erase the stored fault codes immediately after installation to confirm the repair is complete.
Знайшли помилку?
Допоможіть нам стати кращими — якщо ви помітили помилку на сайті або в даних, повідомте нас, і ми виправимо її якнайшвидше.